Viscosity and diffusion coefficient at two salinities and two temperatures.

## Abstract

As discussed in Chapter 6, numerical prediction of swelling can be attempted using existing hyperelastic material models available in commercial finite element (FE) packages. However, none of these models can accurately represent the behavior of swelling elastomers. The major shortcoming of currently available swelling models is that they consider Gaussian statistics for mechanical contribution of configuration entropy, which is based on chains having limited extensibility. Some later models (not yet incorporated into commercial FE packages) can give a reasonable account of certain behavior patterns in swelling elastomers, but do not explain other aspects well. One of the new approaches is to treat swelling elastomers as gels. As described earlier, gels are mostly liquid, yet they behave like solids due to a three-dimensional cross-linked network within the liquid. Many authors consider gel as poro-elastic or porous and use Darcy’s law to model the amount of fluid influx. However, a swollen elastomer mostly consists of the solvent. When an external load is applied, maximum resistance comes from the solvent molecules as in diffusion. Also, most of the new models are quite complex in concept and formulation, and there is a serious need for a scientifically simpler model.

### Keywords

- swelling elastomer
- new material model
- continuum mechanics
- non-Gaussian statistics

## 1. Introduction

As discussed in Chapter 6, numerical prediction of swelling can be attempted using existing hyperelastic material models available in commercial finite element (FE) packages. However, none of these models can accurately represent the behavior of swelling elastomers [1]. The major shortcoming of currently available swelling models is that they consider Gaussian statistics for mechanical contribution of configuration entropy, which is based on chains having limited extensibility [2]. These models assume small stretch of elastomer chains, while swelling elastomers experience much larger stretches. That is why they show only modest agreement with experimental data.

Some later models (not yet incorporated into commercial FE packages) can give a reasonable account of certain behavior patterns in swelling elastomers, but do not explain other aspects well [3]. One of the new approaches is to treat swelling elastomers as gels. As described earlier, gels are mostly liquid, yet they behave like solids due to a three-dimensional cross-linked network within the liquid. Many authors consider gel as poro-elastic or porous and use Darcy’s law to model the amount of fluid influx. However, a swollen elastomer mostly consists of the solvent. When an external load is applied, maximum resistance comes from the solvent molecules as in diffusion. Also, most of the new models are quite complex in concept and formulation, and there is a serious need for a scientifically simpler model.

## 2. Proposed model: salient features

Presented below is the development of a new material model for the prediction of swelling in elastomeric materials, using a continuum mechanics approach. To account for the changes in configuration entropy of the elastomer chains due to swelling, almost all available models [4, 5, 6, 7] use classical Gaussian-statistics in which chains are considered to have limited extensibility [8]. Swelling elastomers undergo large deformations as the chain network stretches more. More realistic non-Gaussian statistics is therefore used for model development here, to account for large mechanical stretches, in terms of mechanical contribution of configuration entropy.

It was concluded in Chapter 6 that Ogden model gives the closest predictions for swelling elastomers [1]. The hyperelastic portion of the new model is therefore based on the phenomenological stretch-based Ogden model. This second-order non-Gaussian strain energy function is used to define changes due to configuration entropy [9]. Rather than treating swelling as an osmosis problem, diffusion is considered to be the mechanism responsible for fluid influx. Flory-Huggins theory is used for incorporating the thermodynamics of mixing of polymer and solvent (absorption of fluid into the elastomer). Unlike other models, which consider only some of the pertinent parameters, proposed model includes most of the relevant material and structural properties of the elastomer, and environmental conditions (temperature, water salinity, coefficient of diffusion, polymer-solvent interaction parameter, etc).

The formulation is based on thermodynamically consistent diffusion-deformation theory for elastomer gels considering the interaction and mixing of polymer and solvent. Solid and liquid like chemical species are considered as a single homogenized continuum [7, 10]. It is assumed that Helmholtz free energy can be divided into network stretching and Fluid-polymer mixing [11]. Flory-Huggins theory is used to describe the changes in entropy due to solid–fluid mixing.

Fluid imbibition in swelling elastomers follows the mechanism of diffusion [4, 12]. Diffusion equations are formulated through suitable balance laws for fluid content. Coefficient of diffusion (

Swelling elastomers are assumed to be incompressible because they possesses high bulk modulus and low shear modulus [13]. Change in volume is negligible as compared to shape change. Gels are soft materials that can deform easily and can undergo volume changes equal to several times its initial volume. This change in volume occurs only as a result of imbibition of solvent molecules. It should be noted that volume of swollen elastomer is the state bounded by material points that deform with the elastomer chains. Swelling of gel actually means deformation of the elastomer network. When a swellable elastomer is placed in a solvent, it absorbs it, resulting in stretching of chains with increase in volume; Figure 2. This unique feature necessitates the consideration of large deformation and helps in developing the mathematical basis for mechanics of swelling. Mathematical structure used to derive deformation of elastomer network due to swelling is similar to the approach used in rubber elasticity. Rubber can be treated as a special case of swelling elastomer with no fluid. Succeeding sections describe the continuum mechanics theory for swelling elastomers.

## 3. Proposed model: mathematical formulation

The new model for swelling in elastomers is developed in this section, describing the relevant contributions of kinematics, force equilibrium, solvent equilibrium, system free energy, kinematic constraint for network incompressibility, kinetics, and thermodynamics of mixing.

### 3.1 Kinematics

Polymer-fluid mixture is considered to be a single homogenized continuum body permitting diffusion of solvent. Reference configuration is a three dimensional dry state of elastomer represented by _{0}. Current configuration represents the deformed swollen state of elastomer network. Intermediate or auxiliary state is the local distortion of elastomer because of volume increase only. Later rotation and stretching of swollen elastomer gives the mechanical elastic deformation in final configuration.

Consider a particle * A*labeled by its position

**in the reference state. Deformation of entire material is described by motion and solvent concentration with smooth mapping of all material particles to the final state. After deformation, particle**X

*attains a new position*A

**in current configuration as shown in Figure 3. Similarly, each particle is deformed and attains a new position in the final sate.**x

Analytical description of the deformation of a continuum can follow either * Eulerian*(spatial) or

*(material) descriptions. In*Lagrangian

*approach, deformation is referred to the current state, while in*Eulerian

*description deformation is referred to reference configuration [14]. In continuum mechanics of solid bodies, spatial description is less beneficial since current configuration is not known. Consider particles*Lagrangian

*and*A

*in Ref. configuration represented by positions*B

X

*and*

_{A}

X

*, respectively. Elemental vector is given by*

_{B}

After deformation at time (** t**), particles occupy spatial positions

x

*and*

_{A}

x

*in current configuration, having elemental vector given by*

_{B}

Displacement of the particles * A*and

*is given by*B

Displacement attained by material in the current configuration can be written as

Relationship between current and reference state (before and after deformation) is expressed by the

A crucial kinematic constituent of the current model is the multiplicative decomposition of the deformation gradient into swelling and mechanical elastic parts as suggested by Flory [11]. Local distortion of the material at X due to swelling is given by

Jacobian is the determinant of deformation gradient such that

Using Eq. (6) and definition of Jacobin from Eq. (7), we can write

### 3.2 Force equilibrium

The principle of virtual work is considered to be a fundamental law in continuum mechanics [15]. It states that the magnitude of virtual work for the forces acting on a particle in equilibrium is zero for any arbitrary virtual motion. The balance of body forces (** b**) per unit volume at equilibrium in reference configuration is given by

where ** ξ**. Multiplying Eq. (9) by this test function and integrating with respect to volume gives

We know that

Eq. (10) thus becomes

Applying Gauss divergence theorem to first term of Eq. (11) transforms the behavior from inside the body to the vector field (** n**) through the surface,

Cauchy’s law states that a stress tensor exists which maps the normal to a surface into traction vector acting on the surface. When applied on Eq. (12) traction boundary loads (** t**) per unit area are added to the equation. Rearranging the terms gives the statement for principle of virtual work:

### 3.3 Solvent equilibrium

Changes in solvent concentration for any material are typically explained through diffusion across the boundary. Let

Applying the divergence theorem to Eq. (14), and rearranging the terms, yields the following balance law for solvent content

For this equation to hold, we must have

The equation for solvent diffusion at the rate (

Multiplying Eq. (16) with an arbitrary test function

Similarly, multiplying Eq. (17) with the same arbitrary test function (

Applying divergence theorem on Eq. (18), putting Eq. (19) in the resultant, and on simplification we get

Chemical potential gradient is required to induce swelling in the polymer. Solvent molecules in dilute phase have higher chemical potential than those in concentrated phase. This difference in potential causes solvent flow from solution to polymer. Chemical potential

### 3.4 Free energy of the system

Free energy density is a function of concentration and deformation gradient. For an element of volume

At equilibrium, free energy of the system is the amount of work done by all the loads and due to solvent transport. For small changes, rate of change of free energy of the system (

Replacing test function with

Dividing Eq. (22) by

Substituting Eqs. (24) and (25) in Eq. (23) and rearranging the terms, we get

According to Clausius-Duhem inequality [17], free energy of a system that is thermodynamically consistent should always decrease or be equal to zero (

When equilibrium in the elastomer is reached between fluid transport and mechanical loads, chemical potential becomes uniform. This can be achieved by equating the second integrand of Eq. (26) to zero, giving the following relation

When free energy density ** )**is defined as a derivative of free-energy with respect to concentration. Extended motion of polymer when volume change occurs due to fluid transport can be explained through kinetics, laying the foundation to develop an expression for flux due to gradient of chemical potential.

### 3.5 Kinematic constraint for network incompressibility

As explained earlier, elastomeric materials have larger values of bulk modulus as compared to shear modulus. They can therefore be considered as almost incompressible. Fluid transporting through the elastomer is assumed to be incompressible as well. Hence, overall response of swollen elastomer can be considered as incompressible. Jacobian can be defined as [6]:

Stretch is the ratio of initial and final linear dimensions that change due to deformation (

In order to embed incompressibility, an integral should be added to the free-energy density function. Using Lagrange multiplier (

Differentiating Eq. (31) with respect to

Stress and chemical potential can now be defined as

### 3.6 Kinetics

The only driving force causing swelling of the elastomer is the amount of fluid transport into the network, resulting in swelling and stretching of networks. This is the reason that kinetics needs to describe the fluid motion in terms of flux and gradient of chemical potential. Some authors consider gel as poro-elastic or porous and use Darcy’s law to model the amount of fluid influx [10, 19]. In porous media, a body is considered to be made up of pores such that permeability is related to the square of pore size. But in a swollen elastomer, major portion of the body is comprised of solvent and when load is applied on it, maximum resistance comes from the solvent molecules as in diffusion. Kinetic theory has also been developed by Tanaka and Fillmore [20] by considering friction with rate-dependent swelling. This theory has limited applicability as it does not consider large deformations. Other authors define a kinetic law based on diffusion mechanism for solvent migrations in elastic material [4, 5, 6]. Mobility tensor should be dependent on deformation gradient and solvent concentration. For defining mobility tensor, we use the relations similar to Chester and Anand [10] and Hong et al. [5]:

Mobility tensor is positive definite and symmetric. Feynman et al. [21] derived an expression for diffusion in which flux is proportional to gradient of chemical potential. It explains the interrelationship of flux, fluid concentration, diffusion, and gradient of chemical potential in terms of true quantities:

In engineering applications, a property based on its original or initial value is termed as nominal quantity. On the other hand, true quantities are based on instantaneous properties. For example, a structural member under the influence of load deforms, resulting in reduction of cross-sectional area. In nominal stresses, the cross-sectional area is assumed constant during the deformation and stress is determined, known as nominal or engineering stress. While in true stress, force is divided by the instantaneous area. True concentration and flux can be converted to nominal values through the relationships

Replacing true concentration and true flux in Eq. (5) by their nominal values, we get

Substituting Eqs. (34) and (36), along with the incompressibility condition from Eq. (30), into Eq. (37), relation for mobility tensor can be obtained:

### 3.7 Thermodynamics of mixing

Thermodynamics involved in polymer and solvent mixing is very important in the development of an analytical model for polymer swelling. The theoretical basis for understanding the behavior of polymer solutions was established independently by Huggins [22] and Flory [23]. Flory-Huggins theory gives the energy of mixing for a pure polymer with a pure solvent in terms of enthalpy and entropy of mixing. Figure 4 presents the lattice model for mixing of polymer and solvent.

Statistical explanation of entropy is used to determine the number of probable positions that the polymer can attain in the solution. Before mixing, both polymer and solvent have no unique state. After mixing, many probable states can be attained, given by

Entropy for free energy of mixing can be specified according to Boltzmann expression as follows:

where

Enthalpy of mixing is defined in terms of a dimensionless entity known as polymer-solvent interaction parameter (

For a closed system at constant pressure and temperature, Gibbs free energy can be defined as

Putting Eqs. (41) and (42) in Eq. (43), we get the expression

Noting that

Substituting Eqs. (45) into Eq. (44), and neglecting the middle term as it is very small compared to the remaining terms, the strain energy density function for mixing (

A similar expression has also been used by Chester and Anand [10] Duda et al. [24] and Kang and Huang [6]. Equation developed by Hong et al. [5] for strain energy density of mixing is different by only a constant value as compared to the above expression, which is negligible in deformation due to swelling. Flory and Rehner [25] postulated that for gels, free energy density is a combination of strain energy density function due to thermodynamics of mixing and stretching of polymer networks:

Strain energy density function for stretching deformation can be based on either Gaussian or non-Gaussian theory. As described earlier, Gaussian theory mainly deals with the scenarios where short stretching of polymer chains is considered, so these models work well only for small deformations and are unable to match the deformation patterns at large strains. Most of the swelling models currently available use Gaussian statistics [8], and are therefore unable to give reasonable predictions for large swelling. Proposed analytical model is based on non-Gaussian theory, while Ogden strain energy function [9] is used to account for the limited extensibility. Ogden model is given by the following relation in terms of principal stretches:

Here,

For the proposed model, second degree Ogden strain energy function is used as it gives the closest prediction (as explained in Chapter 6). Expand Eq. (48) for second degree, and simplifying, we get the following relation:

Putting Eqs. (46) and (50) into (47), we get the following strain energy density function:

Knowing that deformation gradient can be represented as

Differentiation of Eq. (50) with respect to fluid concentration results in the following expression:

Substituting the expressions for

Eq. (54) can be expanded for the three nominal stresses as follows:

On the other hand, the two equations in (54) can be combined to obtain a constitutive relationship for modeling of swelling phenomenon:

Eq. (56) provides a non-linear model for the phenomenon of swelling in elastomeric materials, considering non-Gaussian theory of polymer network stretching. This model takes mechanical as well as solvent properties as input, along with environmental conditions such as temperature, water salinity, swelling medium’s coefficient of diffusion, polymer-solvent interaction parameter, etc.

In order to solve the equations of state, a case of free equilibrium swelling is considered. It is assumed that when dry elastomer is immersed in a solvent, it swells, and equilibrium is achieved after some time. At equilibrium between elastomer and diffusing solvent, chemical potential is negligible. Swelling is considered to be homogenous throughout the elastomer, making stretches equal in all directions. Replacing principal stretches with equivalent swelling stretch (

Using the identity of Eq. (30), we can write

The elastomer is considered to be under no constraint. Application of this no-constraint condition on the elastomer results in no stress. Hence Eq. (58) can be transformed by embedding stress value equals to zero:

## 4. Model validation

Validation of the model developed above requires the comparison of model predictions against experimental results. For this purpose, a series of experiments were performed under specific conditions. Some experimental results are used as input to the model (for evaluation of parameters), while other results are used for model validation. Logical flow of activities for model validation is shown in Figure 5. Swelling related experiments are discussed in detail in Chapters 3 and 7. Experimental work required to determine diffusion coefficients and the polymer-solvent interaction parameter and is explained below.

### 4.1 Experimental investigation

Experiments were conducted (already described in Chapter 7) on disc samples of two different water swelling elastomers, in salt solutions of low and high salinities (0.6% and 12%), at room temperature and 50°C. During the one-month swelling period, readings (volume, thickness, mass, and hardness) were taken before swelling and after 1, 2, 4, 7, 10, 16, 23, and 30 days of swelling. Stres-strain relations from compression and bulk tests were used to determine values of bulk modulus, and different structural properties. Evaluation of other solvent and polymer properties (diffusion coefficient, polymer-solvent interaction parameter, and molar volume of swelling solvent) is discussed below.

#### 4.1.1 Diffusion coefficient

When a dry polymer is immersed into water of a specific salinity, solvent starts diffusing into the polymer due to chemical potential gradient. Diffusion coefficients for low and high salinity solutions should be known in order to correctly predict the amount of swelling. Stokes-Einstein formula [26] is used here to evaluate the diffusion coefficients for low and high salinity solutions.

For a fluid with no flow separation, the drag force is given by

We know that Reynold’s number and cross-sectional area are given by * Re = Dvρ/η*and

*= π*A

D

^{2}/4 respectively. Therefore,

It is known that drag force can also be represented as

where

The diffusion coefficient (D) is given by Einstein’s equation as

Using Stoke’s friction factor, this becomes

Here, * k*is the Boltzmann constant,

*is the absolute temperature,*T

*is the radius of solvent particle, and*R

*is the viscosity.*η

In order to determine diffusion coefficient, viscosity and density of water at low and high salinities are required for all test conditions. To determine the viscosity, Cannon-Fenske [27] apparatus (Figure 6) of size 50 is used. Liquid (whose viscosity is to be determined) is filled in the apparatus slightly above the top-bulb. Fluid is then allowed to flow downwards, pass through the tube, and collect at the bigger bulb at the bottom. Time is recorded for fluid to cross two marks at the top and bottom of the second bulb. Readings are taken at the same temperature at which all swelling related experiments are conducted.

Density of elastomer samples is calculated by determining their mass and volume after each swelling period, for both salinities and at both temperatures. Mass of the elastomer is increased by inflow of salt water into the material. At the same time, volume is increased through swelling. As both mass and volume increase almost proportionally, density does not change too much. Calculated density values are 0.967 g/cm^{3} and 1.016 g/cm^{3} for low salinity water at room temperature and 50°C, and 1.05 g/cm^{3} and 1.0898 g/cm^{3} for high salinity water at the two temperatures respectively.

Mean time for low and high salinity water to pass from the first to the second mark in Cannon-Fenske apparatus was recorded as 157 and 170 sec for 50°C, and 219 and 260 sec at room temperature, respectively. Multiplying by the apparatus factor of 0.004, we get viscosity (centistokes) values of 0.628 and 0.68 at 50°C, and 0.876 and 0.1.04 at room temperature, for low and high salinities respectively. Multiplying this dynamic viscosity with density yields the kinematic viscosity in Pascal-second units. Substituting these values into Eq. (65) gives the required value of diffusion coefficient for each condition. These experimentally determined values of viscosity and diffusion coefficient are summarized in Table 1.

Viscosity (Pa-s x10^{−3}) | Temperature | ||
---|---|---|---|

Low (room) | High (50 °C) | ||

Salinity | Low (0.6%) | 0.89 | 0.607 |

High (12%) | 1.1334 | 0.714 | |

^{2}/s x10^{−10}) | |||

Salinity | Low (0.6%) | 8.22 | 11.65 |

High (12%) | 6.46 | 9.9 |

It can be seen that the diffusion coefficient has higher value in low salinity water as compared to high salinity water, for both room and 50°C temperatures. This higher diffusion amount causes faster swelling rate when the elastomer is kept in low salinity solutions. For same salinity, diffusion coefficient has higher values for higher temperatures, again matching the observed trend for higher amount of elastomer swelling at higher temperature.

Though the mechanism of swelling has been discussed earlier (Chapters 3 and 7), let us revisit the issue in the context of diffusion. When sodium chloride dissolves in water, crystalline structure of sodium and chlorine transform into positive and negative ions surrounded by water molecules. Water molecules close to the ions have strong attraction. When polymer is exposed to brine solution, water molecules diffuse into the empty spaces and begin to fill the voids, resulting in swelling. Ions surrounded by water molecules also enter the polymer but somewhat slowly due to stronger attraction. Ultimately, the polymer is filled by water molecules and ions. Low salinity solution has less number of ions, hence water fills the spaces more quickly as compared to high salinity solution. That is why diffusion takes place at a slower rate in high salinity salt solution.

#### 4.1.2 Polymer-solvent interaction parameter

Polymer-solvent interaction parameter (

The above Eq. (66) is used in this work to determine the value of ^{3}. Values of density of elastomer after different swelling periods are given above. Table 2 lists the experimentally determined values of volume swelling ratio (

Days of Swelling | Volume Swelling Ratio ( | |||
---|---|---|---|---|

Material-A | Material-B | |||

Low-Salinity | High-Salinity | Low-Salinity | High-Salinity | |

1 | 0.455 | 0.543 | 0.494 | 0.646 |

3 | 0.392 | 0.505 | 0.403 | 0.525 |

6 | 0.323 | 0.465 | 0.318 | 0.474 |

9 | 0.291 | 0.431 | 0.292 | 0.442 |

15 | 0.245 | 0.365 | 0.264 | 0.438 |

22 | 0.234 | 0.347 | 0.249 | 0.389 |

30 | 0.234 | 0.338 | 0.232 | 0.376 |

Figure 7 shows the variation of * B*is also consistent with earlier observations about swelling behavior.

### 4.2 Computational code

For the solution of the final Eq. (59) of the developed model, and to extract different values required for analysis, a MATLAB code is written. This requires inputs such as material coefficients, temperature, volume per solvent molecule, interaction parameter, etc. Logical sequence of different steps involved are shown in Figure 8. Using all the input values, and going through the various steps of the iterative scheme, the code estimates the magnitudes of swelling stretches after each swelling period (days) and for each material and each salinity (low and high). Comparison of different outcomes of the model with experimental results is discussed in next section.

## 5. Analysis of results

New model starts with Ogden-2 as its basis, but is changed into a totally new relationship (Eq. 59) by the introduction of terms for diffusion and thermodynamics of mixing. Material coefficients for Ogden model (_{1}, _{12}, _{1}, _{2}) are determined from experimental stress–strain curves and Poisson’s ratio (υ). Polymer-solvent interaction parameter (* ρ*) and chain molecular mass (

*) of the elastomer, molar volume of water (*M

_{c}

V

_{1}), and volume swelling ratio (

*). Other input parameters needed are temperature (*v

_{s}

*), Boltzmann constant (*T

*), and swelled volume per solvent molecule (*k

*) at each stage of swelling, from which the amount of volume and thickness change and the shear modulus (*λ

*) are calculated.*G

### 5.1 Elastomer stretch

Figure 9 gives the variation of stretch for materials * A*and

*under both salinities. Results show an increase in stretch throughout the swelling period for both the materials, sharply in the beginning, then more slowly. This result is in good agreement with the fact that swelling leads to volume increase, which is represented by an increase in the stretch value. Higher stretch values are observed in low salinity solvent, in line with the actual behavior of swelling elastomers which swell more in low salinity due to higher chemical potential gradient and higher diffusion coefficient. Minor fluctuations in the variation of amount of stretch are also similar to the fluctuations in volume and thickness swelling reported and analyzed in Chapters 3 and 7.*B

### 5.2 Volume swelling

Volume after swelling can be calculated from the amount of stretch determined from the model:

Figures 10 and 11 show the comparison between experimental and model-predicted volume at various stages of swelling for materials * A*and

*under the two salinities. Following the pattern of experimental results, predicted amount of elastomer volume increases with swelling time (days). Slight fluctuations in volume swelling are also in line with experimental results, and due to reasons explained earlier. There is a small difference between experimental and model results, the model consistently underestimating the value of volume swelling. This underestimation gives a more conservative estimate of swelling amount, which is better and safer in terms of seal design and development.*B

### 5.3 Thickness swelling

Final thickness after each swelling stage can be calculated using swelling stretch as follows:

Comparison between experimental and predicted values of thickness at various stages of swelling is shown in Figures 12 and 13 for materials * A*and

*in both salinities. There is a gradual increase in the amount of thickness with more days of swelling, with a reasonably good agreement between predicted values and experimental results. As observed earlier, there is more thickness swelling under lower salinity brine.*B

### 5.4 Shear modulus

Amount of stretch predicted from the model can be used to determine the value of shear modulus using the following relationship:

Predicted and experimental values of shear modulus are plotted against swelling time in Figures 14 and 15 for the two materials and salinities. For further comparison, variation of shear modulus through numerical simulation (Chapter 7) using the best available hyperelastic material model (Ogden-2) is also shown. Even though hyperelastic material models are based on the theory of shear, simulated values of

*using the current best model (Ogden-2) show notable variations from the experimental values. As discussed at the end of Chapter 6, hyperelastic models can be used to predict the behavior of swelling elastomers only as a last resort, with some errors. This is mainly because these models do not include the effect of diffusion and thermodynamics of mixing. As the new model includes all these effects, its predictions are much closer to the actual values.*G

This new model is not material-specific, and can be applied to any situation where swelling is taking place. As the use of swelling elastomers in the petroleum industry is a major category of such applications, these results are used here to validate the model predictions. However, the same model can be used to predict the behavior of other soft materials under swelling such as tissue, cartilage, and other biological materials.

## 6. Conclusions

A new analytical model has been developed for predicting the behavior of swelling elastomers, based on nonlinear and non-Gaussian continuum mechanics, different balance laws for forces and solvent (including diffusion), and the thermodynamics of mixing. Including energy, diffusion, and hyperelastic terms, this new model can be used for both constrained and free swelling. Boundary conditions for free swelling are incorporated into the model. A MATLAB code is then developed for model solution. New experiments have been performed to determine input values such as viscosity of swelling medium and polymer-solvent interaction parameter. Stretch values predicted by the model are used to determine volume and thickness swelling, and variation of shear modulus. Model predictions have good agreement with experimental results, much closer than numerical simulation based on best existing hyperelastic material model.